Arctic Cat 425 2011 Скачать руководство пользователя | Manualshive

Страница: 18 / 122

background image

17

738-420A

AL681

2. Compress the brake lever/pedal several times to

check for a firm brake. If the brake is not firm, the

system must be bled.

3. To bleed the brake system, use the following procedure.

A. Remove the cover and fill the reservoir with DOT

4 Brake Fluid.

B. Install and secure the cover; then slowly compress

the brake lever/pedal several times.

C. Remove the protective cap, install one end of a

clear hose onto one FRONT bleeder screw, and

direct the other end into a container; then while

holding slight pressure on the brake lever/pedal,

open the bleeder screw and watch for air bubbles.

Close the bleeder screw before releasing the brake

lever/pedal. Repeat this procedure until no air

bubbles are present.

AF637D

PR377C



NOTE: During the bleeding procedure, watch the

appropriate reservoir very closely to make sure there
is always a sufficient amount of brake fluid. If low,
refill the reservoir before the bleeding procedure is
continued. Failure to maintain a sufficient amount of
fluid in the reservoir will result in air in the system.

D. Repeat step C until the brake lever/pedal is firm.

E. At this point, perform step B, C, and D on the other

FRONT bleeder screw; then move to the REAR

bleeder screw and follow the same procedure.

4. Carefully check the entire hydraulic brake system

that all hose connections are tight, the bleed screws

are tight, the protective caps are installed, and no

leakage is present.

INSPECTING HOSES

Carefully inspect the hydraulic brake hoses for cracks or

other damage. If found, the brake hoses must be replaced.

CHECKING/REPLACING PADS

The clearance between the brake pads and brake discs is

adjusted automatically as the brake pads wear. The only

maintenance that is required is replacement of the brake

pads when they show excessive wear. Check the thick-

ness of each of the brake pads as follows.

1. Remove a front wheel.

2. Measure the thickness of each brake pad.

3. If thickness of either brake pad is less than 1.0 mm

(0.039 in.), the brake pads must be replaced.

CAUTION

Brake fluid that has been drained or bled from the brake
system must NEVER be re-used or severe brake system
corrosion and damage may occur. Always discard used
brake fluid in an appropriate manner.

CAUTION

This hydraulic brake system is designed to use DOT 4
brake fluid only. If brake fluid must be added, care must be
taken as brake fluid is very corrosive to painted surfaces.

Manual

Table of Contents

«
...
16
17
18
19
20
...
»

Содержание 425 2011



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 425 2011

Бренд: Landa Страницы: 101

TRX250EX Sportrax250EX

Бренд: Honda Страницы: 203

2002/24 ATV-300XS

Бренд: HER CHEE Страницы: 56

Бренд: Yamaha Страницы: 21

Бренд: E-ride Industries Страницы: 109

QuicKART 2000 Series

Бренд: Dane Technologies Страницы: 115

Бренд: Taylor-Dunn Страницы: 260

K550ATV EEC 4x4

Бренд: FEISHEN Страницы: 102

2014 TERRAIN 1000 72V CE

Бренд: Ezgo Страницы: 71

Sno Pro 120 2013

Бренд: Arctic Cat Страницы: 61

PROWLER XT 2014

Бренд: Arctic Cat Страницы: 218

Бренд: Yamaha Страницы: 504

Бренд: Ifor Williams Trailers Страницы: 55

Бренд: Range Road Страницы: 6

Бренд: Wood-mizer Страницы: 90

Бренд: Polaris Страницы: 4

Бренд: SCORPION Страницы: 32

Бренд: Rick's Specialty Vehicles Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды