Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 119 / 122

118

5. Remove the screws securing the front body to the

front body supports; then remove the left-side and

right-side footwell fasteners.

KC204A

6. Remove the electric panel; then disconnect the LCD

gauge connector, ignition switch, and accessory out-

let.

KC210G

7. Remove the front body panel/fender panel.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively, cracked,

or damaged in any way, replacement is necessary.

1. Clean all fender components with warm soap and

water.

2. Inspect fenders for cracks and/or loose rivets.

3. Inspect for any missing decals.

INSTALLING

1. Making sure the shift spring is in place and the shift

lever is properly positioned, place the front body

panel/fender panel onto the ATV. With the front rack

in place, loosely install the front rack hardware.

2. Connect the electrical connectors under the electric

panel; then connect the light connectors and attach

onto the frame.

KC210G

KC224

3. Install the screws securing the front body to the front

body supports; then install the left-side and right-side

footwell fasteners. Do not tighten at this time.

4. Place the gas tank cover into position and secure

with the existing hardware; then install the two cap

screws securing the rear of the panel to the frame.

Tighten all cap screws and fasteners securely.

5. Install the electric panel, side panels, and seat.

Exhaust System

REMOVING MUFFLER

1. Remove the two exhaust springs at the muf-

fler/exhaust pipe juncture.

KC170

2. Slide the muffler rearward to clear the mounting lugs

and remove the muffler. Account for a grafoil seal.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды