Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 27 / 122

Removing Top-Side

Components

A. Cylinder Head Cover/Rocker Arms
B. Cylinder Head/Camshaft



NOTE: Remove the spark plug, timing inspection

plug, and outer magneto cover; then using an appro-
priate wrench, rotate the crankshaft to top-dead-cen-
ter of the compression stroke.



NOTE: Arctic Cat recommends the use of new gas-

kets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmission.

1. Remove the cap screws securing the two valve

inspection covers. Remove the two covers. Account

for the O-rings.

FI603



NOTE: Keep the mounting hardware with the covers

for assembly purposes.

2. Remove the cylinder head cover cap screws. Note

the rubber washers on the four top-side cap screws;

remove the cylinder head cover. Note the orientation

of the cylinder head plug and remove it. Note the

location of the two alignment pins.

FI606A

MD1354A

3. Remove the cap screw from the tension adjuster;

then using a common screwdriver, relax the cam

chain tension by rotating the adjuster screw clock-

wise until it locks.

FI607A

FI608

5. Bend the washer tabs and remove the two cap screws

securing the sprocket to the camshaft.

FI612

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды