Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 66 / 122

Gas Tank

REMOVING

1. Disconnect the negative battery cable; then remove

the seat and side panels.

2. Remove the cap screws (A) securing the rear of the

front body to the frame; then remove two reinstall-

able rivets (B) securing the gas tank cover to the

body.

KC219A

3. Remove the gas tank cap; then remove the gas tank

cover. Place gas tank cap back on tank.

KC220

4. Remove the cap screw securing the gas tank to the frame

and using a suitable block, support the rear of the tank;

then remove the clamp securing the gasline hose. Discon-

nect the gas line connector from the fuel pump outlet.

KC241A

5. Using a suitable block, hold the front body open and

remove the gas tank to the rear. Account for the heat

shield.

KC260

KC262

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively, cracked,

or damaged in any way, replacement is necessary.

1. Clean all gas tank components with parts-cleaning

solvent.

2. Inspect all hoses for cracks or leaks.

3. Inspect tank cap and tank for leaks, holes, and dam-

aged threads.

! WARNING

Whenever any maintenance or inspection is made on
the fuel system during which there may be fuel leakage,
there should be no welding, smoking, open flames, etc.,
in the area.

! WARNING

Gasoline may be under pressure. Place an absorbent
towel under the connector to absorb any gasoline spray
when disconnecting.

! WARNING

Do not turn the ignition switch to the ON position with
the hoses removed. Gasoline will be pumped by the
electric fuel pump causing a safety hazard.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды