Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 74 / 122

3300A



NOTE: Not using a battery charger with the proper

float maintenance will damage the battery if con-
nected over extended periods.

Charging



NOTE: Arctic Cat recommends the use of the CTEK

Multi US 800 or the CTEK Multi US 3300 for battery
maintenance charging.

1. Be sure the battery and terminals have been cleaned

with a baking soda and water solution.



NOTE: The sealing strip should NOT be removed

and NO fluid should be added.

2. Be sure the charger and battery are in a well-venti-

lated area. Be sure the charger is unplugged from the

110-volt electrical outlet.

3. Connect the red terminal lead from the charger to the

positive terminal of the battery; then connect the

black terminal lead of the charger to the negative ter-

minal of the battery.

4. Plug the charger into a 110-volt electrical outlet.

5. By pushing the Mode button (A) on the left side of

the charger, select the Normal Charge Icon (E). The

Normal Charge Indicator (C) should illuminate on

the upper left portion of the charger.

6. The battery will charge to 95% of its capacity at

which time the Maintenance Charge Indicator (D)

will illuminate.



NOTE: For optimal charge and performance, leave

the charger connected to the battery for a minimum 1
hour after the Maintenance Charge Indicator (D) illu-
minates. If the battery becomes hot to the touch, stop
charging. Resume after it has cooled.

7. Once the battery has reached full charge, unplug the

charger from the 110-volt electrical outlet.



NOTE: If, after charging, the battery does not perform

to operator expectations, bring the battery to an autho-
rized Arctic Cat dealer for further troubleshooting.

RPM Limiter



NOTE: The ATV is equipped with an ECU that

retards ignition timing when maximum RPM is
approached. When the RPM limiter is activated, it
could be misinterpreted as a high-speed misfire.

Testing Electrical

Components

All of the electrical tests should be made using the Fluke

Model 73 Multimeter or Fluke Model 77 Multimeter and

when testing peak voltage, the Peak Voltage Reading

Adapter must be used. If any other type of meter is used,

readings may vary due to internal circuitry. When trou-

bleshooting a specific component, always verify first that

the fuse(s) are good, that the bulb(s) are good, that the

connections are clean and tight, that the battery is fully

charged, and that all appropriate switches are activated.



NOTE: For absolute accuracy, all tests should be

made at room temperature of 68° F.

Accessory

Receptacle/Connector



NOTE: This test procedure is for either the recepta-

cle or the connector.

VOLTAGE

1. Turn the ignition switch to the ON position; then set

the meter selector to the DC Voltage position.

2. Connect the red tester lead to the red wire; then con-

nect the black tester lead to ground.

3. The meter must show battery voltage.



NOTE: If the meter shows no battery voltage, trou-

bleshoot the battery, fuse, receptacle, connector, or
the main wiring harness.

Brakelight Switch

(Pressure)

The brakelight switch is located on the top of the auxil-

iary brake master cylinder and is pressure activated by

the hand brake or the auxiliary brake pedal. This switch

also activates the start-in-gear (SIG) relay in the power

distribution module (PDM).



NOTE: The ignition switch must be in the ON position.

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды