Arctic Cat 425 2011 страница 31 Скачать руководство пользователя

Страница: 31 / 122

CC134D

CC136D



NOTE: The valve seals must be replaced.

3. Remove the valve springs; then invert the cylinder

head and remove the valves.

Measuring Valve Stem Runout

1. Support each valve stem end with the V Blocks; then

check the valve stem runout using a dial indicator.

ATV-1082

2. Maximum runout must not exceed specifications.

Measuring Valve Stem Outside
Diameter

1. Using a micrometer, measure the valve stem outside

diameter.

2. Acceptable diameter rangesmust be within specifications.

Measuring Valve Face/Seat Width

1. Using a calipers, measure the width of the valve face.

FI367

2. Acceptable width must be at or above specifications.

Measuring Valve Face Radial
Runout

1. Mount a dial indicator on the surface plate; then

place the valve stem on a set of V blocks.

2. Position the dial indicator contact point on the out-

side edge of the valve face; then zero the indicator.

ATV1082A

3. Rotate the valve in the V blocks.

4. Maximum runout must not exceed specifications.

Measuring Valve Guide/Valve Stem
Deflection (Wobble Method)

1. Mount a dial indicator and base on the surface plate;

then place the cylinder head on the surface plate.

2. Install the valve into the cylinder head; then position

the dial indicator contact point against the outside

edge of the valve face. Zero the indicator.

CC131D

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды