Arctic Cat 425 2011 страница 48 Скачать руководство пользователя

Страница: 48 / 122

MD1036

. Using a 6 mm cap screw threaded into the fixed

driven face, spread the driven pulley by turning the
cap screw clockwise; then remove the V-belt.

KC132

6. Remove the fixed drive face.

MD1094

Remove the nut holding the driven pulley assembly;
then remove the driven pulley assembly.

MD1068

8. Using an impact screwdriver, remove the three Phil-

lips-head cap screws holding the air intake plate.

Remove the air intake plate.

MD1092

9. Remove the cap screws holding the clutch cover onto

the right-side crankcase half. Note the positions of the

different-lengthed cap screws for installing purposes

10. Using a rubber mallet, loosen

the clutch cover;

then

pull it away from the right-side crankcase half.

Account for two alignment pins and gasket.

MD1115

D. Centrifugal Clutch Assembly
E. Oil Pump Drive Gear
F. Oil Pump Driven Gear
G. Oil Pump



NOTE: Steps 1-10 in the preceding sub-section

must precede this procedure.

11. Remove the one-way clutch noting the direction of the

green dot or the word OUTSIDE for installing purposes.

MD1286

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды