Arctic Cat 425 2011 Скачать руководство пользователя

Страница: 84 / 122

1. Connect the three-wire plug to the sensor; then

remove the mounting screws securing the sensor to

the frame.

KC339E

2. Install the needle adapters to the multimeter leads;

then select DC Voltage on the multimeter.

3. Connect the red tester lead to the blue/brown wire

(B) and the black tester lead to the pink/black wire

(A); then turn the ignition switch ON and observe the

meter. The meter should read 0.3-1.5 DC volts.

KC416A

4. Tilt the sensor 60° or more to the left and right

observing the meter. The meter should read 3.0-7.0

DC volts after approximately one second in the tilted

position. If the meter readings are not as specified,

the tilt sensor is defective.

KC414A

KC416B

Throttle Position Sensor

(TPS)

INSPECTING

1. Remove the left-side engine cover; then disconnect

the three-wire TPS connector plug.

PR544



NOTE: Prior to testing the TPS, inspect the three-wire

plug connector on the main harness and the three-pin
plug on the TPS for contamination, broken pins, and/or
corrosion.

2. Make sure the ignition switch is in the OFF position;

then select the DC Voltage position on the meter.

3. Connect the black tester lead to terminal B and the red

tester lead to terminal A. Turn the ignition switch to the

ON position. The meter should read approximately 5.0

DC volts.

PR538A

Manual

Table of Contents

Содержание 425 2011



























































































































Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды

Arctic Cat 425 2011, Руководство по обслуживанию

Результаты поиска

Содержание 425 2011

Отзывы:

Похожие инструкции для 425 2011

Бренды по названию

Популярные бренды