Arctic Cat 425 2011 Скачать руководство пользователя | Manualshive

Страница: 111 / 122

background image

110

CHECKING/INFLATING

1. Using an air pressure gauge, measure the air pressure

in each tire. Adjust the air pressure as necessary to

meet the recommended inflation pressure.

2. Inspect the tires for damage, wear, or punctures.



NOTE: If repair is needed, follow the instructions

found on the tire repair kit or remove the wheel and
have it repaired professionally.



NOTE: Be sure all tires are the specified size and

have identical tread pattern.

3. Check the front wheel toe-in and toe-out and adjust

as necessary (see Steering/Frame/Controls section).

4. Test drive the ATV on a dry, level surface and note

any pulling to the left or right during acceleration,

deceleration, and braking.



NOTE: If pulling is noted, measure the circumfer-

ence of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking only,
check and adjust the brakes as necessary and
recheck operation (see Periodic Maintenance sec-
tion).

5. Increase the air pressure in the tires with the smallest

circumference measurement until all tires are equal

in circumference.

6. Repeat steps 4-5 as necessary to ensure proper han-

dling.

Troubleshooting

! WARNING

Do not operate the ATV if tire damage exists.

Problem: Suspension too soft

Condition

Remedy

1.

Spring(s)

weak

2.

Shock absorber

damaged

3.

Shock absorber preload

too low

1. Replace spring(s)
2. Replace shock absorber
3. Adjust shock absorber preload

Problem: Suspension too stiff

Condition

Remedy

1.

A-arm-related bushings

worn

2.

Shock absorber preload

too high

1. Replace bushing
2. Adjust shock absorber preload

Problem: Suspension noisy

Condition

Remedy

1.

Cap screws (suspension system)

loose

2.

A-arm-related bushings

worn

1. Tighten cap screws
2. Replace bushings

Problem: Rear wheel oscillation

Condition

Remedy

1.

Rear wheel hub bearings

worn - loose

2.

Tires

defective - incorrect

3.

Wheel rim

distorted

4.

Wheel hub cap screws

loose

5.

Auxiliary brake

adjusted incorrectly

6.

Rear suspension arm-related bushing

worn

7.

Rear shock absorber

damaged

8.

Rear suspension arm nut

loose

1. Replace bearings
2. Replace tires
3. Replace rim
4. Tighten cap screws
5. Adjust brake
6. Replace bushing
7. Replace shock absorber
8. Tighten nut

Manual

Table of Contents

«
...
109
110
111
112
113
...
»

Содержание 425 2011



























































































































Отзывы:

Нет отзывов

Похожие инструкции для 425 2011

700 Diesel ATV 2007

Бренд: Arctic Cat Страницы: 184

WILD HP 300 - SERVICE

Бренд: GAS GAS Страницы: 65

Бренд: TGB Страницы: 209

545 XC ATV EU 2011

Бренд: KTM Страницы: 221

600 INDY Voyager 2014

Бренд: Polaris Страницы: 132

600 INDY SP 2019

Бренд: Polaris Страницы: 178

QuicKART 2000 Series

Бренд: Dane Technologies Страницы: 115

Бренд: Humbaur Страницы: 36

Stand-Up SINGLE RIDE-UP Go Series

Бренд: Kendon Страницы: 20

Бренд: Arctic Cat Страницы: 124

Бренд: Toro Страницы: 12

EcoLight MPG585

Бренд: Malone Страницы: 9

Бренд: Ace Sports Страницы: 34

Бренд: Opus Страницы: 21

Бренд: HAUL MASTER Страницы: 2

Бренд: McKee Страницы: 18

Yukon II CXL-150

Бренд: Eton Страницы: 31

Lightning-AXL50

Бренд: Eton Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды