Amazone Cataya 3000 Super Скачать руководство пользователя страница 99

Страница: 99 / 252

Layout and function

Cataya Super BAH0087-11 01.19

5.18.3

Seeding without exact following harrow (exact following harrow lift)

The exact following harrow can be lifted
independently of the position of the coulters.

A hydraulic cylinder (Fig. 106/1) lifts the exact
following harrow.

Depending on the implement equipment,
actuation of the exact following harrow lift with a
tractor control unit is possible in 2 variations.

The exact following harrow lift can be actuated
with a tractor control unit



with Comfort hydraulic system
after selection on the control terminal



without Comfort hydraulic system
with the tractor control unit (blue) configured
specifically for this purpose.

Fig. 106

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды