Amazone Cataya 3000 Super Скачать руководство пользователя страница 154

Страница: 154 / 252

Settings

154

Cataya Super BAH0087-11 01.19

Pre-calibrating the implement

7. Pre-calibrate the seed drill.

Pre-calibration creates the same conditions
as when driving on the field later on.

7.1 Insert the central key (Fig. 195/1) on

the hexagon.

7.2 Using the central spanner, turn the

seeding shaft to the left until the seed
falls into the collection bucket from all
of the seed housings.

Fig. 195

7.4 Empty the two-part collection bucket

(Fig. 196/1) into the seed hopper, put
together, and push it into the holder up
to the stop with the bucket opening
facing up.

Fig. 196

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды