Amazone Cataya 3000 Super Скачать руководство пользователя страница 135

Страница: 135 / 252

Coupling and uncoupling the implement

Cataya Super BAH0087-11 01.19

135

7.3.2

Uncoupling – Soil tillage implement and pack top seed drill

DANGER

Empty the hopper before decoupling the pack top seed drill
from the soil tillage implement.

WARNING

Danger of being crushed, cut, caught, drawn in or struck
through insufficient stability and possible tilting of the
uncoupled implement!

Set the empty implement down on a horizontal parking area with a
firm base.

1. Switch off the tractor PTO shaft.

2. If the implement is equipped with coulter lifting and the coulters are lifted, lower the coulters into

working position.

Only combinations with TwinTeC double disc coulters:

3. Set the placement depth to "0", see section "Adjusting and checking the seed placement depth",

page 164.

All combinations:

4. Park the combination on a level surface with solid ground.

5. Empty the hopper.

6. Move the combination into transport position, see section "Moving the seeding combination into

transport position", page 185.

7. Set the coulter pressure to "0", see section "Coulter pressure, seed rate increase and coulter lift",

page 168.

8. Apply the tractor parking brake, switch the tractor engine off and remove the ignition spanner.

9. Uncouple the supply lines connected to the

tractor.

10. Hang the supply lines in the hose cabinet

(Fig. 158).

Fig. 158

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды