Amazone Cataya 3000 Super Скачать руководство пользователя страница 176

Страница: 176 / 252

Settings

176

Cataya Super BAH0087-11 01.19

8.10.3

Setting the roller contact pressure

1. Adjust the roller contact pressure with the

central spanner (Fig. 231), see
section 5.19, page 100.

2. Check the seed placement depth after each

adjustment, see section 8.6.1, page 161.

Fig. 231

3. Check the roller contact pressure to the

soil, e.g. with a spring balance
(see Fig. 232).

Fig. 232

Roller diameter D

Roller contact

pressure F

250 mm

max. 20 kg

To prevent damage to the roller
harrow, the roller contact pressure
"F" must not exceed the table value.

Lifting the roller harrow off of the ground

A scale (Fig. 233/1) underneath the control centre
indicates the set roller pressure of the roller
harrow in percent.

The roller harrow is lifted off of the ground when
the central spanner is turned counter-clockwise
(-) and the pointer exceeds the 0%-mark.

As soon as the roller harrow has been raised, the
indicator points to the symbol (Fig. 233/2), see
also section 5.19,

page

100.

Fig. 233

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды