Amazone Cataya 3000 Super Скачать руководство пользователя страница 170

Страница: 170 / 252

Settings

170

Cataya Super BAH0087-11 01.19

8.8.2.1

Increasing / reducing the coulter pressure

1. Actuate the tractor control valve (green).



The pointer (Fig. 217/1) shows the current

coulter pressure on the scale.



The hydraulic cylinder of the exact following

harrow moves against the stop inserted in
the adjuster segment, see section 8.9,
page 172.



With the corresponding pointer setting

(Fig. 217/2), the seed rate is increased, see
section 8.8.2.2.

Fig. 217

8.8.2.2

Adjusting the seed rate increase

1. Set the pointer (Fig. 218/1) to the desired

scale value.
The pointer indicates the coulter pressure
scale mark above which the increased rate
should be spread.

2. Hand-tighten the wing nuts.

Fig. 218

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды