Amazone Cataya 3000 Super Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 100

Layout and function

100

Cataya Super BAH0087-11 01.19

5.19

Roller harrow

This option is only possible in combination with
RoTeC Control coulters.

The roller harrow consists of



harrow tines (Fig. 107/1)



press rollers (Fig. 107/2).

The harrow tines close the seed furrows.

The press rollers press the seeds into the
furrows. Better soil contact means more humidity
is available for germination. Voids are closed and
obstruct snails' access to the seed.

Fig. 107

The following are adjustable



the pitch of the harrow tines



the working depth of the harrow tines



the roller contact pressure.

If the roller harrow is not being used, it can be raised.

The adjuster segment (Fig. 108/1) serves to
adjust the harrow tines.

Fig. 108

Adjustments can be made to



the pitch of the harrow tines



the working depth of the harrow tines.

«
...
98
99
100
101
102
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды