Amazone Cataya 3000 Super Скачать руководство пользователя страница 101

Страница: 101 / 252

Layout and function

Cataya Super BAH0087-11 01.19

101

The central spanner (Fig. 109) is used to
adjust the roller contact pressure.

Fig. 109

The carrying arms of the roller harrow are
spring suspended on a rotating tube. As a
result, the rollers can follow the contours of the
ground.

The roller contact pressure is adapted to the
ground by rotating the tube.

Turning the central spanner



Clockwise (+):

Increase roller
contact pressure



Counter-

clockwise (-):

Reduce roller
contact pressure

Fig. 110

Setting tip:

Dry soil:

increase roller
contact
pressure

Moist soil:

decrease roller
contact
pressure

A scale (Fig. 111/1) underneath the control
centre shows the set roller contact pressure in
percent.

If the roller harrow is not being used, it can be
raised.

The roller harrow is lifted when the central
spanner is turned counter-clockwise (-) and the
pointer has underranged the 0% mark. As soon
as the roller harrow is lifted, the pointer points to
the symbol (Fig. 111/2).

Fig. 111

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды