Amazone Cataya 3000 Super Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 125

Coupling and uncoupling the implement

Cataya Super BAH0087-11 01.19

125

7.2

Coupling and uncoupling implements

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

You may only connect the implement to tractors suitable for the
purpose.

WARNING

Risk of contusions, cutting, catching, drawing in and knocks
when the implement unexpectedly releases from the tractor!



Use the intended equipment to connect the tractor and the
implement in the proper way.



When coupling the implement to the tractor's three-point
hydraulic system, ensure that the attachment categories of the
tractor and the implement are the same.



Whenever you couple the implement, check the coupling parts,
such as the top link pin, for visible defects. Replace the coupling
parts in the event of clearly visible wear.



Secure coupling parts such as the top link bolt with a linch pin so
that they do not accidentally detach.

WARNING

Risk of contusions when coupling the implement and standing
between the tractor and the implement!

Instruct people to leave the danger area between the tractor and the
implement before you approach the implement.

Any helpers may only act as guides standing next to the tractor and
the implement, and may only move between the vehicles when both
are at a standstill.

CAUTION

Only connect the implement when



the tractor and implement are coupled



the tractor parking brake is applied



the tractor engine is switched off and



the ignition spanner has been removed.

«
...
123
124
125
126
127
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды