Amazone Cataya 3000 Super Скачать руководство пользователя страница 49

Страница: 49 / 252

Product description

Cataya Super BAH0087-11 01.19

4.5.4

Comfort hydraulic system - Implements with ISOBUS system

Identification

of the hydraulic

hose lines

Connection of the

tractor control unit

Function when actuating the tractor control unit

yellow

Single

acting

Track marker

Lifting and lowering, alternating

Tramline marker

Lifting and lowering,
depending on the tramline counter

green

Double-

acting

Coulter pressure

adjustment

Seed rate increase

- Activation on the coulter pressure adjuster segment
- Increased rate setting on the control terminal

Coulter lift

Parking / working position

Exact following harrow pressure

adjustment

red

Pressureless return flow

Important!
Always connect this hydraulic line to the
tractor.

The connection of this hydraulic line to the tractor is
required for all hydraulic functions.

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды