Amazone Cataya 3000 Super Скачать руководство пользователя страница 88

 

 

Layout and function 

 

 

88

 

Cataya Super  BAH0087-11  01.19

 

5.16 

TwinTeC double disc coulter 

The TwinTeC double disc coulter (Fig. 86/1) is 
used for plough seeding and mulch seeding. 

Harvest residues are cut by the large double disc 
coulters, clearing the plant residues evenly to the 
side and forming a clean seed furrow. 

The seed falls between the seeding discs into 
the seed furrow opened by the double discs. 

The parallel-guided double disc coulters are 
supported on the press rollers (Fig. 86/2) and 
therefore precisely maintain the seed placement 
depth. 

The rubberised press rollers close the seed 
furrow. The displaced soil beside the double disc 
coulters is levelled by the harrow tines  
(Fig. 86/3). 

 

 

Fig. 86 

 

The pitch and the working depth of the harrow tines (Fig. 86/3) can be adjusted.  

The pitch can be adjusted in three positions: "flat", "medium" and "steep", see section 8.7.1,  

page 

165. 

 

If the press rollers (Fig. 86/2) sink in slightly on loose soil, press rollers with a wider contact area can 
be installed. 

 

 

 

Содержание Cataya 3000 Super





























































































































































































































































Отзывы: