Amazone Cataya 3000 Super Скачать руководство пользователя страница 227

Страница: 227 / 252

Cleaning, maintenance and repairs

Cataya Super BAH0087-11 01.19

227

Do not adjust the hexagon socket
screw (Fig. 307/1) of the metering
wheels. They have a slight
circumferential backlash in the
seeding shaft groove.

The tramline metering wheels can
rotate freely on the seeding shaft.

Fig. 307

Removing the seeding shaft half that is driven via the coupling

6. Two adjustment rings (Fig. 308/1) rest

closely on a seed housing. Thus, they
secure the right half of the seeding shaft
axially.

Loosen the hexagon socket screws of the
adjustment rings.

Fig. 308

7. Loosen the hexagon socket screw

(Fig. 309/1) of the seeding shaft coupling.

8. Pull the seeding shaft half (Fig. 309/2) out

of the implement side part.

Fig. 309

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды