Amazone Cataya 3000 Super Скачать руководство пользователя страница 142

Страница: 142 / 252

Settings

142

Cataya Super BAH0087-11 01.19

8.1

Folding the steps up and down

DANGER

Never climb onto the steps and the loading board when the seed
drill is parked on the supports (risk of tipping).

Climbing up is only permitted when the seed drill is coupled to the soil
tillage implement.

CAUTION

Only step onto the loading board via the steps.

Climbing onto the loading board without using the steps can lead to
serious injuries due to falling.

Always fold up the steps before starting operation or road transport.

DANGER

A latch (Fig. 173) represents the
mechanical transport locking
mechanism for the steps.

Check the latch (arrow) for proper
seating after folding in the steps.

Fig. 173

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды