Amazone Cataya 3000 Super Скачать руководство пользователя страница 158

Страница: 158 / 252

Settings

158

Cataya Super BAH0087-11 01.19

8.4.2

Calibrating the seed rate
Implements with AmaDrill 2 control terminal,
Implements with ISOBUS system

1. Prepare the implement for calibration, see

section " Calibrating the seed rate",
page 151.

2. Pre-calibrate the seed drill.

2.1 Pre-calibrate the seed drill according

to the "ISOBUS software" operating
manual.
Pre-calibration creates the same
conditions as when driving on the field
later on.

2.2 Empty the two-part collection bucket

(Fig. 191/1) into the seed hopper, put
together, and push it into the holder up
to the stop with the opening facing up.

Fig. 200

3. Calibrating the seed rate.

3.1 Calibrate the seed drill according to

the "ISOBUS software" operating
manual.

3.2 Fold out the bracket (Fig. 201/1) for

weighing the collected seed.

3.3 Weigh the content of the collection

bucket in the collapsible bucket.

Fig. 201

Check the scales to ensure the display
is accurate, taking the container weight
into consideration.

4. Repeat the calibration test until the desired

seed rate is achieved.

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды