Amazone Cataya 3000 Super Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 36

General safety instructions

36

Cataya Super BAH0087-11 01.19

2.16.5

Operation of the seed drill



Observe the permissible filling quantity of the hopper.



Use the ladder and the loading board only for filling the hopper.

It is forbidden to ride on the implement during operation.



When calibrating the seed rate, pay attention to the danger
points from rotating and oscillating implement parts.



Do not place any parts in the hopper.



Lock the track marker (construction-dependent) in transport
position before road transport.

2.16.6

Cleaning, maintenance and repair



Only carry out cleaning, maintenance and repair work on the
implement when:



the control terminal is switched off



the implement plug is disconnected from the tractor
e.g. ISOBUS plug



the drive is switched off



the tractor engine is at a standstill



the ignition spanner has been removed.



Regularly check the nuts and bolts for a firm seat and retighten
them as necessary.



Secure the raised implement or raised implement parts against
unintentional lowering before performing any cleaning,
maintenance or repair work on the implement.



When replacing work tools with blades, use suitable tools and
gloves.



Dispose of oils, greases and filters in the appropriate manner.



Disconnect the cable to the tractor generator and battery before
performing electrical welding work on the tractor and mounted
implements.



Spare parts must at least comply with the specified technical
requirements of AMAZONEN-WERKE. This is ensured through
the use of genuine AMAZONE spare parts.

«
...
34
35
36
37
38
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды