Amazone Cataya 3000 Super Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 132

Coupling and uncoupling the implement

132

Cataya Super BAH0087-11 01.19

12. Raise the combination so that the parking

supports are just above the ground.

13. Remove the parking supports (Fig. 149/1).

Fig. 149

DANGER

Remove the parking supports immediately after coupling the
seed drill on the soil tillage implement.

The parking supports do not have a locking device. When transporting
the combination, they can accidentally wander out of the mounts and
cause serious accidents.

Connect the hydraulic hose (Fig. 150/1) for the
track markers.

Fig. 150

14. Connect the plug (Fig. 151/1):



Plug and socket connection
lighting on the left for road travel.



Plug and socket connection
lighting on the right for road travel.

Fig. 151

«
...
130
131
132
133
134
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды