Amazone Cataya 3000 Super Скачать руководство пользователя страница 172

Страница: 172 / 252

Settings

172

Cataya Super BAH0087-11 01.19

8.9

Adjusting the exact following harrow

8.9.1

Adjusting the exact following harrow tines

Only seed drills with exact following harrow lift

1. Insert the central spanner.

2. Set the distance "A", see Fig. 100, page 96.

3. Insert the central spanner into the transport

bracket, see section 5.7, page 64.

Fig. 221

Only seed drills without exact following harrow lift

1. Set distance "A" (see Fig. 100, page 96) by

adjusting the turnbuckle (Fig. 222/1).

2. Secure the setting with the lock nut

(Fig. 222/2).

3. Make the same settings on both

turnbuckles.

Fig. 222

CAUTION

The maximum allowed length of the
turnbuckle may not be exceeded
(see Fig. 223).

When the specified length is
exceeded, the turnbuckle can break
off.

Fig. 223

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды