Amazone Cataya 3000 Super Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 62

Layout and function

62

Cataya Super BAH0087-11 01.19

5.3

AMAZONE calibration button

The calibration button (Fig. 40) in the control
centre is connected to the control terminal in the
tractor cab. When actuating the calibration
button, the metering motor to calibrate the seed
rate or empty the seed hopper starts running.

The calibration button can be used on
implements with and without ISOBUS system.

The calibration button cannot be connected to
the control terminal.

The calibration button (Fig. 40) is not required if
the implement is equipped with the
TwinTerminal.

A detailed description can be found in the



"AmaDrill 2" operating manual



"ISOBUS software" operating manual.

Fig. 40

5.4

Control terminal for implements with ISOBUS system

The combination can be equipped with the ISOBUS system. Implements with the ISOBUS system
have a job computer that is installed in a protected position on the implement. The job computer
control the hydraulic cylinders and electric motors, monitors the implement functions, and implements
the inputs on the control terminal made by the tractor driver.

The ISOBUS system makes it possible to connect the implement to any ISOBUS control terminal. If
the tractor has an ISOBUS system, the AMAZONE job computer can be connected to the existing
ISOBUS socket of the tractor and operated with the on-board terminal.

It must be noted that functions are not executed if the control terminal does not have the
corresponding software. If the control terminal does not have the "Section Control" software,
GPS signals cannot be processed with the implement.

Instructions for operating the AMAZONE job computer with ISOBUS system can be found in the
"ISOBUS software" operating manual.

«
...
60
61
62
63
64
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды