Amazone Cataya 3000 Super Скачать руководство пользователя страница 45

Страница: 45 / 252

Product description

Cataya Super BAH0087-11 01.19

4.4

Safety and protective equipment

(1) 2 bars serve as a mechanical transport lock

for the track markers on the soil tillage
implement, see also "Soil tillage implement"
operating manual.

Fig. 18

(1) Handrail

Fig. 19

(1) Charging sieve in the seed hopper.

Prevents contact with the running agitator
shaft.
The charging sieve can only be opened with
the central spanner.

Fig. 20

(1) Function flap.

Prevents contact with the chain drive of the
seeding and agitator shafts. The function
flap can only be opened with the central
key.

Fig. 21

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды