Amazone Cataya 3000 Super Скачать руководство пользователя страница 51

Страница: 51 / 252

Product description

Cataya Super BAH0087-11 01.19

4.7

Intended use

The implement



is designed for metering and spreading certain commercially available seeds during agricultural
work



is mounted on an AMAZONE soil tillage implement with roller approved for this purpose



is coupled to the tractor three-point hitch together with the soil tillage implement and is operated
by one person.

Slopes can be travelled



Across the slope

Direction of travel to left: 10 %

Direction of travel to right: 10 %



Up/down the slope

Up the slope: 10 %

Down the slope: 10 %.

Intended use also includes



compliance with all the instructions in this operating manual



adherence of inspection and maintenance work



exclusive use of genuine AMAZONE spare parts.

Other uses to those specified above are forbidden and shall be considered as improper.

For any damage resulting from improper use



the operator bears the sole responsibility



AMAZONEN-WERKE accepts no liability.

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды