Amazone Cataya 3000 Super Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 252

Amazone Cataya 3000 Super Скачать руководство пользователя страница 13

General safety instructions

Cataya Super BAH0087-11 01.19

13

Risks in handling the implement

The implement has been constructed to the state-of-the art and the
recognised rules of safety. However, operating the implement may
cause risks and restrictions



the health and safety of the user or third persons



the implement itself



other property.

Only use the implement



for the purpose for which it was intended



in a perfect state of repair.

Eliminate any faults immediately which could impair safety.

Guarantee and liability

Our "General conditions of sales and delivery" are always applicable.
These shall be available to the operator, at the latest on conclusion of
the contract. Guarantee and liability claims for damage to people or
property will be excluded if they can be traced back to one or more of
the following causes:



Improper use of the implement



Improper installation, commissioning, operation and
maintenance of the implement



Operation of the implement with defective safety equipment or
improperly attached or non-functioning safety and protective
equipment



Non-compliance with the instructions in the operating manual
regarding commissioning, operation and maintenance



Unauthorised design changes to the implement



Insufficient monitoring of implement parts which are subject to
wear



Improperly executed repairs



Disasters due to the effects of foreign objects and force majeure.

«
...
11
12
13
14
15
...
»

Содержание Cataya 3000 Super





























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды