Amazone Cataya 3000 Super Скачать руководство пользователя страница 184

Страница: 184 / 252

Settings

184

Cataya Super BAH0087-11 01.19

8.14

Moving the exact following harrow road safety bar into road
transport/parking position

8.14.1

Moving the road safety bar into road transport position

1. Push the two-part road safety bar

(Fig. 246/1) over the tine tips of the exact
following harrow.

2. Fasten the road safety bar with spring

holders (Fig. 246/2) to the exact following
harrow.

Fig. 246

8.14.2

Moving the transport safety bar into parking position

Insert the road safety bars (Fig. 247/1) into
each other.

Fig. 247

Attach the assembled road safety bar to the
transport bracket (Fig. 248/2) with the spring
holders (Fig. 248/1).

Fig. 248

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды