Amazone Cataya 3000 Super Скачать руководство пользователя страница 188

Страница: 188 / 252

Transportation

188

Cataya Super BAH0087-11 01.19

WARNING

Risk of crushing, cutting, being caught and/or drawn in, or
impact from tipping and insufficient stability.



Drive in such a way that you always have full control over the
tractor with the attached machine.

In so doing, take your personal abilities into account, as well as

the road, traffic, visibility and weather conditions, the driving
characteristics of the tractor and the connected or coupled
implement.



Before transportation, fasten the side locking device of the
tractor lower link so that the mounted or towed implement
cannot swing back and forth.

WARNING

Danger of breaking during operation, insufficient stability and
insufficient tractor steering and braking power on improper use
of the tractor!

These risks pose serious injuries or death.

Observe the permissible total weight of the mounted implement
combination and the permissible axle and drawbar loads of the
tractor.

WARNING

Risk of falling when riding on the implement, contrary to
instructions.

It is forbidden to ride on the implement and/or climb the implement
while it is running.

WARNING

Other road users can be endangered by carried loads falling
down!

It is forbidden to carry loads on the loading board of the implement.

Содержание Cataya 3000 Super





























































































































































































































































Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды

Amazone Cataya 3000 Super, Руководство по эксплуатации

Результаты поиска

Содержание Cataya 3000 Super

Отзывы:

Бренды по названию

Популярные бренды