ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 11 / 176

External activation of ZCVPSOF..................................................60
Automatic initiation of ZCVPSOF.................................................61
Completing the test.......................................................................61

Testing current protection functions........................................................61

Instantaneous phase overcurrent protection 3-phase output

PHPIOC (50)......................................................................................61

Measuring the operate limit of set values.....................................62
Completing the test.......................................................................62

Instantaneous phase overcurrent protection phase segregated

output SPTPIOC (50)........................................................................62

Completing the test.......................................................................63

Four step phase overcurrent protection 3-phase output

OC4PTOC (51_67)............................................................................63

Verifying the settings....................................................................63
Completing the test.......................................................................64

Four step phase overcurrent protection phase segregated

output OC4SPTOC (51_67)...............................................................64

Verifying the settings....................................................................65
Completing the test.......................................................................66

Instantaneous residual overcurrent protection EFPIOC (50N)..........66

Measuring the operate limit of set values.....................................66
Completing the test.......................................................................67

Four step residual overcurrent protection, zero or negative

sequence direction EF4PTOC (51N/67N).........................................67

Four step directional residual overcurrent protection ..................67
Four step non-directional residual overcurrent protection............68
Completing the test.......................................................................68

Sensitive directional residual overcurrent and power protection

SDEPSDE (67N)................................................................................68

Measuring the operate and time limit for set values.....................68
Completing the test.......................................................................74

Thermal overload protection, one time constant, Fahrenheit/

Celsius LFPTTR/LCPTTR (26)..........................................................74

Testing the protection without external temperature

compensation (NonComp)............................................................74
Completing the test.......................................................................75

Breaker failure protection, phase segregated activation and

output CCRBRF (50BF).....................................................................75

Checking the phase current operate value,

Pickup_PH...............76

Checking the residual (ground fault) current operate value

Pickup_N set below Pickup_PH....................................................76

Table of contents

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды