ABB Relion 650 Series REL650 страница 98 Скачать руководство пользователя | Manualshive

Страница: 98 / 176

background image

6.4.15

Directional overpower protection GOPPDOP (32)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for GOPPDOP (32) are available on the local HMI under

Main menu/Tests/Function status/Current/GOPPDOP(32,P>)/X:GOPPDOP

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.4.15.1

Verifying the settings

The overpower protection shall be set to values according to the real set values to be
used. The test is made by means of injection of voltage and current where the
amplitude of both current and voltage and the phase angle between the voltage and
current can be controlled. During the test the analog outputs of active and reactive
power shall be monitored.

1.

Connect the test set for injection of voltage and current corresponding to the
mode to be used in the application. If a three phase test set is available this could
be used for all the modes. If a single phase current/voltage test set is available the
test set should be connected to a selected input for one phase current and voltage.
Use the formulas stated in

for the different calculation modes used. The

set mode

Mode

can be found under

Main menu/Settings/IED Settings/Current/

GOPPDOP(32,P>)/1:GOPPDOP/General

.

2.

Adjust the injected current and voltage to the set rated values in % of

IBase

and

VBase

(converted to secondary current and voltage). The angle between the

injected current and voltage shall be set equal to the set direction

Angle1

, angle

for stage 1 (equal to 0° for low forward power protection and equal to 180° for
reverse power protection). Check that the monitored active power is equal to
100% of rated power and that the reactive power is equal to 0% of rated power.

3.

Change the angle between the injected current and voltage to

Angle1

+ 90°.

Check that the monitored active power is equal to 0% of rated power and that the
reactive power is equal to 100% of rated power.

4.

Change the angle between the injected current and voltage back to

Angle1

value.

Increase the current slowly from 0 until the PICKUP1 signal, pickup of stage 1, is
activated. Check the injected power and compare it to the set value

Power1

,

power setting for stage 1 in % of

Sbase

.

5.

Increase the current to 100% of

IBase

and switch the current off.

6.

Switch the current on and measure the time for activation of TRIP1, trip of stage 1.

7.

If a second stage is used, repeat steps

for the second stage.

Section 6

1MRK 506 331-UUS A

Testing functionality

90

Commissioning Manual

«
...
96
97
98
99
100
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: Da-Lite Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Muirhead Страницы: 28

Бренд: Wöhner Страницы: 9

Бренд: TCi Страницы: 2

RELION 670 SERIES REG670

Бренд: ABB Страницы: 134

Бренд: JVC Страницы: 69

Бренд: JVC Страницы: 71

Бренд: Kemo Electronic Страницы: 2

Steel Weave Grille

Бренд: Cornell Страницы: 50

RELION 650 SERIES

Бренд: ABB Страницы: 128

DBI Sala 3400800C

Бренд: 3M Страницы: 24

Бренд: Zenith Страницы: 54

Dual Pro Series

Бренд: Sordin Страницы: 22

Бренд: Isotronic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды