manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 63

Table 

7

 is used together with figure 

14

.

6.3.2.1 

Measuring the operate limit of set values

1.

Supply the IED with healthy conditions for at least two seconds.

2.

Apply the fault condition and slowly decrease the measured impedance to find
the operate value for of the phase-to-ground loop ECG, test point 1, according to
figure 

13

. Compare the result of the measurement with the expected value

according to table 

6

.

The corresponding binary signals that inform about the operation of the phase
selection measuring elements are available in the local HMI under

Main menu/Tests/Function status/Impedance/FDPSPDIS

.

3.

Repeat steps 

1

 to 

2

 to find the operate values for the remaining test points

according to figure 

13

 and table 

6

.

4.

Repeat steps 

1

 to 

3

 to find the operate value for the phase-to-phase fault in A - C

according to figure 

14

 and table 

7

.

6.3.2.2 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

to 

Disabled

 under 

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/

Function test modes/Impedance/FDPSPDIS/1:FDPSPDIS

 for the function, or for

each individual function in a chain, to be tested next. Remember to set the parameter

Blocked

 to 

Yes

, for each individual function that has been tested.

6.3.3 

Faulty phase identification with load encroachment

FMPSPDIS (21)

There is no specific test routine for this function. The function is tested in conjunction
with other impedance (mho) functions.

6.3.4 

Phase preference logic PPLPHIZ

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to

verify settings"

.

1MRK 506 331-UUS A

Section 6

Testing functionality

55

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды