ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 141 / 176

No TRIP signal should appear.

12. Switch the fault current and the polarizing voltage off.
13. Reset the BLOCK digital input.

Permissive scheme

Inject the polarizing voltage 3V0, which is 5% of

VBase

where the current is

lagging the voltage by 65°.

Inject current (65° lagging the voltage) into one phase at about 110% of the set
operating current, and switch the current off with the switch.

Switch the fault current on, (110% of the set operating current) and wait longer
than the set value

tCoord

No TRIP signal should appear, and the CS binary output should
be activated.

Switch the fault current off.

Activate the CR binary input.

Switch the fault current on (110% of the set operating current) and measure the
operating time of the ECPSCH (85) logic.
Use the TRIP signal from the configured binary output to stop the timer.

Compare the measured time with the setting for

tCoord

Activate the BLOCK digital input.

Switch the fault current on (110% of the set operating current) and wait for a
period longer than the set value

tCoord

No TRIP signal should appear.

10. Switch the fault current and the polarizing voltage off.
11. Reset the CR binary input and the BLOCK digital input.

6.9.5.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Scheme communication/ECPSCH(85)/1:ECPSCH

for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter

Blocked

Yes

, for each individual function that has been tested.

1MRK 506 331-UUS A

Section 6

Testing functionality

133

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды