ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 160 / 176

Table 14:

Internal fault indications

Fault indication

Additional information

Internal Fault

Real Time Clock Error

Hardware error with the real time clock.

Internal Fault

Runtime Exec. Error

One or more of the application threads

are not working properly.

Internal Fault

SW Watchdog Error

This signal will be activated when the

terminal has been under too heavy

load for at least 5 minutes.

Internal Fault

Runtime App Error

One or more of the application threads

are not in an expected state.

Internal Fault

File System Error

A file system error has occurred.

Internal Fault

TRM-Error

A TRM card error has occurred. The

instance number is displayed at the

end of the fault indication.

Internal Fault

COM-Error

A COM card error has occurred. The

instance number is displayed at the

end of the fault indication.

Internal Fault

PSM-Error

A PSM card error has occurred. The

instance number is displayed at the

end of the fault indication.

8.2.2

Warnings

The warning message associated with the fault is found in the internal event list in the
LHMI menu

Main menu/Diagnostics/Internal events

. The message includes the date,

time, description and signal state for the fault. The current status of the internal fault
signals can also be checked via the LHMI in

Main menu/Diagnostics/IED status/

General

When a fault appears, record the fault indication message and state it when ordering
service.

Table 15:

Warning indications

Warning indication

Additional information

Warning

IEC 61850 Error

IEC 61850 has not succeeded

in some actions such as

reading the configuration file,

startup etc.

Warning

DNP3 Error

Error in DNP3 communication.

Section 8

1MRK 506 331-UUS A

Troubleshooting

152

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды