ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 103 / 176

6.6

Testing frequency protection functions

6.6.1

Underfrequency protection SAPTUF (81)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for SAPTUF (81) are available on the local HMI under

Main menu/Tests/Function status/Frequency/SAPTUF(81,f<)/X:SAPTUF

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.6.1.1

Verifying the settings

Verification of PICKUP value and time delay to operate

Check that the IED settings are appropriate, especially the PICKUP value and the
definite time delay.

Supply the IED with three-phase voltages at their rated values.

Slowly decrease the frequency of the applied voltage, until the PICKUP signal
appears.

Note the operate value and compare it with the set value.

Increase the frequency until rated operating levels are reached.

Check that the PICKUP signal resets.

Instantaneously decrease the frequency of the applied voltage to a value about
20% lower than the operate value.

Measure the time delay of the TRIP signal, and compare it with the set value.

Extended testing

The test above can be repeated to check the time to reset.

The tests above can be repeated to test the frequency dependent inverse time
characteristic.

Verification of the low voltage magnitude blocking

Check that the IED settings are appropriate, especially the

PUFrequency

and the

tDelay

and the

MinValFreqMeas

in the SMAI preprocessing function.

Supply the IED with three-phase voltages at rated values.

Slowly decrease the magnitude of the applied voltage, until the BLKDMAGN
signal appears.

Note the voltage magnitude value and compare it with the SMAI set value

MinValFreqMeas

1MRK 506 331-UUS A

Section 6

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды