ABB Relion 650 Series REL650 страница 83 Скачать руководство пользователя | Manualshive

Страница: 83 / 176

background image

Monitor the signal ALARM until it appears on the corresponding binary output or
on the local HMI.

5.

Compare the measured temperature with the setting.

6.

Measure the LFPTTR/LCPTTR (26)protection trip time.
Use the TRIP signal from the configured binary output to stop the timer.

7.

Take the TEMP readings.
Compare with the setting of

TripTemp

.

8.

Activate the BLOCK binary input.
The signals ALARM, RI and TRIP should disappear.

9.

Reset the BLOCK binary input.

10. Check the reset limit (TdReset).

Monitor the signal PICKUP until it disappears on the corresponding binary output
or on the local HMI, take the TEMP readings and compare with the setting of

ReclTemp

.

11. Compare the measured trip time with the setting according to the formula.
12. Reset the thermal memory.
13. Continue to test another function or end the test by changing the test mode setting

to

Disabled

.

6.4.8.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Current/LFPTTR(26,T>)/1:LFPTTR

,

Main menu/Tests/

Function test modes/Current/LCPTTR(26,T>)/1:LCPTTR

for the function, or for

each individual function in a chain, to be tested next. Remember to set the parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.4.9

Breaker failure protection, phase segregated activation and

output CCRBRF (50BF)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for CCRBRF (50BF) are available on the local HMI under

Main menu/Tests/Function status/Current/CCRBRF(50BF)/1:CCRBRF

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

The Breaker failure protection, 3-phase activation and output function CCRBRF
(50BF) should normally be tested in conjunction with some other function that
provides an initiate signal. An external INITIATE signal can also be used.

1MRK 506 331-UUS A

Section 6

Testing functionality

75

Commissioning Manual

«
...
81
82
83
84
85
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

ABS-Lock X-Flat LX Series

Бренд: ABS Страницы: 8

Бренд: Husqvarna Страницы: 28

Бренд: Husqvarna Страницы: 247

Бренд: Pentair Страницы: 2

DuraTech Cable SRL

Бренд: Falltech Страницы: 31

Бренд: Panasonic Страницы: 26

Бренд: Merlin Страницы: 18

Бренд: Richards Страницы: 53

Бренд: Trinity Страницы: 72

Бренд: Showa Denki Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды