ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 13 / 176

Completing the test.......................................................................92

Two step residual overvoltage protection ROV2PTOV (59N)...........93

Verifying the settings....................................................................93
Completing the test.......................................................................93

Loss of voltage check LOVPTUV (27)...............................................93

Measuring the operate limit of set values.....................................94
Completing the test.......................................................................94

Testing frequency protection functions...................................................95

Underfrequency protection SAPTUF (81)..........................................95

Verifying the settings....................................................................95
Completing the test.......................................................................96

Overfrequency protection SAPTOF (81)...........................................96

Verifying the settings....................................................................96
Completing the test.......................................................................97

Rate-of-change frequency protection SAPFRC (81).........................97

Verifying the settings....................................................................97
Completing the test.......................................................................98

Testing secondary system supervision functions...................................98

Current circuit supervision CCSRDIF (87).........................................98

Verifying the settings....................................................................99
Completing the test.......................................................................99

Fuse failure supervision SDDRFUF...................................................99

Checking that the binary inputs and outputs operate as

expected ....................................................................................100
Measuring the operate value for the negative sequence

function ......................................................................................100
Measuring the operate value for the zero-sequence

function ......................................................................................101
Checking the operation of the dv/dt and di/dt based

function ......................................................................................101
Completing the test.....................................................................102

Testing control functions.......................................................................102

Synchrocheck, energizing check, and synchronizing SESRSYN

(25)..................................................................................................103

Testing the synchronizing function.............................................105
Testing the synchrocheck check................................................106
Testing the energizing check......................................................110
Testing the voltage selection......................................................111
Completing the test.....................................................................112

Autorecloser for 3-phase operation SMBRREC (79).......................112

Preparation of the verification ....................................................114

Table of contents

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды