ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 89 / 176

To verify the settings in the most common back-up trip mode

1 out of 3

it is sufficient

to test phase-to-ground-faults.

At mode

2 out of 4

the Phase current setting,

Pickup_PH

can be checked by single

phase injection where the return current is connected to the summed current input. The
value of residual (EF) current IN set lower than

Pickup_PH

is most easily checked in

backup trip mode

1 out of 4

6.4.10.1

Checking the phase current operate value, Pickup_PH

Check the current level

IP>

where setting

FunctionMode

Current

and setting

BuTripMode

1 out of 3

2 out of 4

as set under

Main menu/Settings/IED Settings/

Current/CSPRBRF(50BF)/1:CSPRBRF

Apply the fault condition, including INITIATION of CSPRBRF (50BF), with a
current below set

Pickup_PH

Repeat the fault condition and increase the current in steps until a trip occurs.

Compare the result with the set

Pickup_PH

Disconnect AC and INITIATE input signals.

If “No IPickup check” or “

Retrip off

” is set, only back-up trip can

be used to check set

Pickup_PH

6.4.10.2

Checking the residual (GF) current operate value

IN> set below IP>

Check the low set

IN>

current where setting

FunctionMode

Current

and setting

BuTripMode

1 out of 4

as set under

Main menu/Settings/IED Settings/Current/

CSPRBRF(50BF)1:CSPRBRF

Apply the fault condition, including initiation of CSPRBRF 50BF, with a current
just below set

Pickup_N

Repeat the fault condition and increase the current in steps until trip appears.

Compare the result with the set

Pickup_N

Disconnect AC and initiation input signals.

6.4.10.3

Checking the re-trip and back-up times

The check of the set times can be made in connection with the check of operate values
above. Choose the applicable function and trip mode, such as

FunctionMode

Current

and setting

RetripMode

No CBPos Check

as set under

Main menu/Settings/IED

Settings/CSPRBRF(50BF)/Current/1:CSPRBRF

1MRK 506 331-UUS A

Section 6

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды