ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 76 / 176

background image

For inverse time curves, check the operate time at a current equal to 110% of the
operate current for

txMin

.

9.

Check that all trip and trip contacts operate according to the configuration (signal
matrixes)

10. Reverse the direction of the injected current and check that the step does not operate.
11. Check that the protection does not operate when the polarizing voltage is zero.
12. Repeat the above described tests for the higher set steps.
13. Finally, check that pickup and trip information is stored in the event menu.

6.4.6.2

Four step non-directional residual overcurrent protection

1.

Do as described in

"Four step directional residual overcurrent protection"

, but

without applying any polarizing voltage.

6.4.6.3

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Current/EF4PTOC(51N67N,4IN>)/X:EF4PTOC

for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.4.7

Sensitive directional residual overcurrent and power

protection SDEPSDE (67N)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for SDEPSDE (67N) are available on the local HMI under

Main menu/Tests/Function status/Current/SDEPSDE(67N,IN<->)/1:SDEPSDE

.

The Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

6.4.7.1

Measuring the operate and time limit for set values

Operation mode 3I

0

· cosφ

Procedure

1.

Set the polarizing voltage to 1.2 ·

VNRelPU

and the phase angle between voltage

and current to the set characteristic angle (

RCADir

), the current lagging the voltage.

Section 6

1MRK 506 331-UUS A

Testing functionality

68

Commissioning Manual

«
...
74
75
76
77
78
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: Magnavox Страницы: 54

Бренд: Dräger Страницы: 104

GEPARD PREMIUM-CHE

Бренд: DEVA Страницы: 13

Бренд: Zenith Страницы: 28

Бренд: Zenith Страницы: 98

Бренд: Veris Industries Страницы: 2

Бренд: TALOS Страницы: 20

Бренд: Save Phace Страницы: 8

Бренд: Husqvarna Страницы: 36

Бренд: Sony Страницы: 158

Бренд: Sony Страницы: 39

Бренд: Sony Страницы: 35

Бренд: ABB Страницы: 196

Бренд: ABB Страницы: 8

Бренд: ABB Страницы: 17

REF615 ANSI 5.0 FP1

Бренд: ABB Страницы: 80

Бренд: TFortis Страницы: 11

Бренд: Professional Tool Products Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды