ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 87 / 176

Set

BuTripMode

2 out of 4

Apply the fault condition, including initiation of CCRBRF (50BF), with one-
phase current above set

Pickup_PH

and residual (ground fault) above set

Pickup_N

Verify that back-up trip is achieved after set time. If selected, re-trip should also
appear.

Apply the fault condition, including initiation of CCRBRF (50BF), with at least
one-phase current below set

Pickup_PH

and residual (ground fault) above set

Pickup_N

. The current may be arranged by feeding three- (or two-) phase

currents with equal phase angle (I0-component) below

Pickup_PH

, but of such

value that the residual (ground fault) current (3I

) will be above set value

Pickup_N

Verify that back-up trip is not achieved.

Disconnect AC and INITIATE input signals.

6.4.9.6

Verifying the case

RetripMode = Contact

It is assumed that re-trip without current check is selected,

RetripMode

Contact

Set

FunctionMode

Contact

Apply input signal for CB closed to input 52a_A (B or C).

Apply input signal, for initiation of CCRBRF (50BF).

Verify that phase selection re-trip and back-up trip are achieved after set times.

Disconnect the trip signal. Keep the CB closed signal.

Apply input signal, for initiation of CCRBRF (50BF).

Arrange disconnection of CB closed signal well before set back-up trip time

Verify that back-up trip is not achieved.

Disconnect injected AC and INITIATE input signals.

6.4.9.7

Verifying the function mode

Current&Contact

To be made only when

FunctionMode

Current&Contact

is selected.

Checking the case with fault current above set value

Pickup_PH

The operation shall be as in

FunctionMode

Current

Set

FunctionMode

Current&Contact

Leave the inputs for CB close inactivated. These signals should not influence.

Apply the fault condition, including initiation of CCRBRF (50BF), with current
above the set

Pickup_PH

value.

Check that the re-trip, if selected, and back-up trip commands are achieved.

Disconnect injected AC and INITIATE input signals.

1MRK 506 331-UUS A

Section 6

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды