ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 139 / 176

the function, or for each individual function in a chain, to be tested next. Remember to
set the parameter

Blocked

Yes

, for each individual function that has been tested.

6.9.4

Local acceleration logic ZCLCPLAL

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for ZCLCPLAL are available on the local HMI under

Main menu/Tests/Function status/Scheme communication/ZCLCPLAL/
1:ZCLCPLAL

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

The logic is checked during the secondary injection test of the impedance measuring
zones.

6.9.4.1

Verifying the settings

Provide the IED with conditions equivalent to normal load for at least two seconds.

Deactivate the conditions for accelerated function.

Apply a phase-to-ground fault at 100% of line impedance.

Check that the fault is tripped with the second zone time delay.

Provide the IED with conditions equivalent to normal load for at least two seconds.

Activate the condition for accelerated function either by the autorecloser or by the
loss-of-load.

Apply a phase-to-ground fault at 100% of line impedance.

Check that the fault is tripped instantaneously.

6.9.4.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Scheme communication/ZCLCPLAL/1:ZCLCPLAL

for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter

Blocked

Yes

, for each individual function that has been tested.

6.9.5

Scheme communication logic for residual overcurrent

protection ECPSCH (85)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

1MRK 506 331-UUS A

Section 6

Testing functionality

131

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды