manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 95

Values of the logical signals for BRCPTOC (46) are available on the local HMI under

Main menu/Tests/Function status/Current/BRCPTOC(46,lub)/X:BRCPTOC

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.4.13.1 

Measuring the operate and time limit of set values

1.

Check that the input logical signal BLOCK to the BRCPTOC (46) function block
is logical zero and note on the local HMI that the output signal TRIP from the
BRCPTOC (46) function block is equal to the logical 0.

2.

Set the measured current (fault current) in one phase to about 110% of the set
operating current 

IP>

.

Observe to not exceed the maximum permitted overloading of the current circuits
in the terminal.

3.

Switch on the fault current and measure the operating time of BRCPTOC (46).
TRIP is controlled by Gate 13 in the configuration.
Use the TRIP signal from the configured binary output to stop the timer.

4.

Compare the measured time with the set value 

tOper

.

5.

Activate the BLOCK binary input.

6.

Switch on the fault current (110% of the setting) and wait longer than the set
value 

tOper

.

No TRIP signal should appear.

7.

Switch off the fault current.

8.

Set the measured current (fault current) in same phase to about 90% of the set
operating current 

IP>

. Switch off the current.

9.

Switch on the fault current and wait longer than the set value 

tOper

.

No TRIP signal should appear.

10. Switch off the fault current.

6.4.13.2 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

to 

Disabled

 under 

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/

Function test modes/Current/BRCPTOC(46,lub)/X:BRCPTOC

 for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter 

Blocked

 to 

Yes

, for each individual function that has been tested.

6.4.14 

Directional underpower protection GUPPDUP (37)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to

verify settings"

.

1MRK 506 331-UUS A

Section 6

Testing functionality

87

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды