ABB Relion 650 Series REL650 страница 92 Скачать руководство пользователя

Страница: 92 / 176

Apply the fault and the initiate again. The value of current should be below the
set value

Pickup_BlkCont

Arrange disconnection of BC closed signal(s) well before set back-up trip time

It simulates a correct CB tripping.

Verify that back-up trip is not achieved. Re-trip can appear for example, due to
selection "Re-trip without current check".

Disconnect injected AC and initiation of input signals.

6.4.10.8

Checking the phase current operate value,

Pickup_PH

Check the low set

Pickup_PH

current where setting

FunctionMode

Current

and

setting

BuTripMode

1 out of 3

2 out of 4

as set under

Main menu/Settings/IED

Settings/Current/CSPRBRF(50BF)/1:CSPRBRF

Apply the fault condition, including pickup of CSPRBRP (50BF), with a current
just below set

Pickup_PH

Repeat the fault condition and increase the current in steps until trip appears.

Compare the result with the set

Pickup_PH

Disconnect AC and pickup input signals.

NoIPickupcheck

Retrip off

is set, only back-up trip can be used to

check set

Pickup_PH

6.4.10.9

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Current/CSPRBRF(50BF)/1:CSPRBRF

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

Yes

, for each individual function that has been tested.

6.4.11

Stub protection STBPTOC (50STB)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Logical signals for STBPTOC (50STB) protection are available on the local HMI
under

Main menu/Tests/Function status/Current/STBPTOC(50STB)/1:STBPTOC/

Inputs or Outputs

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды