manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 60

or for each individual function in a chain, to be tested next. Remember to set the
parameter 

Blocked

 to 

Yes

, for each individual function that has been tested.

6.3.2 

Phase selection with load encroachment, quadrilateral

characteristic FDPSPDIS (21)

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for FDPSPDIS are available on the local HMI under

Main menu/Tests/Function status/Impedance/FDPSPDIS/1:FDPSPDIS

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

The phase selectors operate on the same measuring principles as the impedance
measuring zones. So it is necessary to follow the same principles as for distance
protection, when performing the secondary injection tests.

Measure operating characteristics during constant current conditions. Keep the
measured current as close as possible to the rated value of its associated input
transformer, or lower. But ensure that it is higher than the set minimum operating current.

Ensure that the maximum continuous current to the IED does not exceed four times its
rated value, if the measurement of the operating characteristics runs under constant
voltage conditions.

To verify the settings the operating points according to figures 

13

 and 

14

 should be

tested. See also tables 

6

 and 

7

 for information.

Section 6

1MRK 506 331-UUS A

Testing functionality

52

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды