manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 145

This function is functionality tested together with other protection functions (ground-
fault overcurrent protection, and so on) within the IED. It is recommended that the
function is tested together with the autorecloser function, regardless of whether the
autorecloser function is integrated or external.

6.10.1.1 

Three-phase operating mode

1.

Check that 

AutoLock

 and 

TripLockout

 are both set to 

Disabled

.

2.

Initiate a three-phase fault.
An adequate time interval between the faults should be considered, to overcome
areset time caused by the possible activation of the Autorecloser function,
SMBRREC (79). The function must issue a three-pole trip in all cases, when a
trip is initiated by any protection function, either integrated or external. The
functional TRIP output signal must always appear.

6.10.1.2 

Circuit breaker lockout

The following tests should be carried out when the built-in lockout function is used in
addition to possible other tests, which depends on the complete configuration of an
IED.

1.

Check that 

AutoLock

 and 

TripLockout

 are both set to 

Disabled

.

2.

Initiate a three-phase fault.
The functional output TRIP should be active at each fault. The output CLLKOUT
must not be activated.

3.

Activate the automatic lockout function, set 

AutoLock 

 = 

Enabled

 and repeat.

Besides the TRIP outputs, CLLKOUT should be set.

4.

Reset the lockout signal by activating the reset lockout (RSTLKOUT) signal.

5.

Activate the TRIP signal lockout function, set 

TripLockout

 = 

Enable

 and repeat.

The output TRIP must be active and stay active after each fault. CLLKOUT must
be activated.

6.

Reset the lockout.
All functional outputs should reset.

7.

Deactivate the TRIP signal lockout function, set 

TripLockout

 = 

Disabled

 and the

automatic lockout function, set 

AutoLock

 = 

Disabled

 if not used.

6.10.1.3 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

to 

Disabled

 under 

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/

Function test modes/Logic/SMPPTRC(94,1->0)/X:SMPPTRC

 for the function, or

1MRK 506 331-UUS A

Section 6

Testing functionality

137

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды