ABB Relion 650 Series REL650 страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 176

background image

6.3.1.3

Measuring the operating limit of set values with shaped load

encroachment characteristics

1.

Subject the IED to healthy normal load conditions for at least two seconds.

2.

Apply the fault condition and slowly decrease the measured impedance to find
the operating value of the phase-to-phase fault A-B for zone 1 according to test
point 1 in figure

. Compare the result of the measurement with the

set value.

3.

to find the operating value for the remaining test points.

Observe that the zones that are not tested have to be blocked and the zone that is
tested has to be released.

4.

to find the operating value for the phase-to-ground fault C-E

according to figure

Test point 6 is intended to test the directional line of impedance
protection. Since directionality is a common function for all 5
measuring zones, it is only necessary to test point 6 once, in the
forward direction. Directional functionality testing (trip inside, no-
trip outside) should always be carried for all impedance zones set
with directionality (forward or reverse).

6.3.1.4

Measuring the operate time of distance protection zones

1.

Subject the IED to healthy normal load conditions for at least two seconds.

2.

Apply the fault condition to find the operating time for the phase-to-phase fault
according to test point 7 in figure

for zone 1. Compare the result of

the measurement with the setting

t1PP

.

3.

to find the operating time for the phase-to-ground fault

according to test point 7 in figure

. Compare the result of the

measurement with the setting

t1PE

.

4.

to find the operating time for all other used measuring zones.

Observe that the zones that are not tested have to be blocked and the zone that is
tested has to be released.

6.3.1.5

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Impedance/ZQMPDIS(21,Z<)/1:ZQMPDIS

for the function,

1MRK 506 331-UUS A

Section 6

Testing functionality

51

Commissioning Manual

«
...
57
58
59
60
61
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: WILLTEK Страницы: 28

Бренд: NEC Страницы: 34

Бренд: NEC Страницы: 32

Бренд: STI Страницы: 2

Бренд: DIADEM Страницы: 20

C-FLAP Quick Mount

Бренд: Markwort Страницы: 2

SecPath T1000 Series

Бренд: H3C Страницы: 13

Бренд: Arcteq Страницы: 359

Бренд: BERMAD Страницы: 6

Бренд: Panasonic Страницы: 103

Бренд: Panasonic Страницы: 50

Бренд: Panasonic Страницы: 180

Бренд: Panasonic Страницы: 44

Бренд: Sony Страницы: 57

Бренд: Sony Страницы: 173

Бренд: Zenith Страницы: 40

ACP Hardwire Series

Бренд: Transtector Страницы: 2

Бренд: Marena Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды