ABB Relion 650 Series REL650 страница 106 Скачать руководство пользователя

Страница: 106 / 176

Check that the appropriate settings are available in the IED, especially the
PICKUP value and the definite time delay. Set

PickupFreqgrad

, to a rather small

negative value.

Supply the IED with three-phase voltages at their rated values.

Slowly decrease the frequency of the applied voltage, with an increasing rate-of-
change that finally exceeds the setting of

PickupFreqgrad

, and check that the

PICKUP signal appears.

Note the operate value and compare it with the set value.

Increase the frequency to rated operating conditions, and zero rate-of-change.

Check that the PICKUP signal resets.

Instantaneously decrease the frequency of the applied voltage to a value about
20% lower than the nominal value.

Measure the time delay for the TRIP signal, and compare it with the set value.

Extended testing

The test above can be repeated to check a positive setting of

PickupFreqGrad

The tests above can be repeated to test the RESTORE signal, when the frequency
recovers from a low value.

6.6.3.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Frequency/SAPFRC(81,df/dt)/X:SAPFRC

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

Yes

, for each individual function that has been tested.

6.7

Testing secondary system supervision functions

6.7.1

Current circuit supervision CCSRDIF (87)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for CCSRDIF (87) are available on the local HMI under

Main menu/Tests/Function status/Secondary system supervision/
CCSRDIF(87,INd)/X:CCSRDIF

. The Signal Monitoring in PCM600 shows the same

signals that are available on the local HMI.

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды