ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 100 / 176

The test above can now be repeated for step

The tests above can be repeated for

2 out of 3

and for

3 out of 3

operation mode.

The tests above can be repeated to check security, that is, the PICKUP and
operate signals, that are not supposed to appear, - do not.

The tests above can be repeated to check the time to reset.

The tests above can be repeated to test the inverse time characteristic.

6.5.1.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Voltage/UV2PTUV(27,2U<)/1:UV2PTUV

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

Yes

, for each individual function that has been tested.

6.5.2

Two step overvoltage protection OV2PTOV (59)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for OV2PTOV (59) are available on the local HMI under

Main menu/Tests/Function status/Voltage/OV2PTOV(59,2U>)/1:OV2PTOV

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

6.5.2.1

Verifying the settings

Apply single-phase voltage below the set value

Pickup1

Slowly increase the voltage until the PU_ST1 signal appears.

Note the operate value and compare it with the set value.

Switch the applied voltage off.

Set and apply about 20% higher voltage than the measured operate value for one
phase.

Measure the time delay for the TRST1 signal and compare it with the set value.

Repeat the test for step

6.5.2.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Voltage/OV2PTOV(59,2U>)/1:OV2PTOV

for the function, or

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды